How do I connect my subwoofer to my sound system?

Speaker Level Inputs

  1. Connect the subwoofer via the ‘B’ or second speaker output.
  2. For subwoofers equipped with a speaker-level input and a speaker-level output, simply connect the receiver speaker outputs to the speaker-level input on the subwoofer and the speaker-level output of the subwoofer to your speakers.

How do I activate my subwoofer?

If you are using your subwoofer with a home theater receiver, the connection is simple: Just run an audio interconnect cable like this one from the receiver’s subwoofer output to the subwoofer’s line input (pictured above). If the subwoofer has an input labeled LFE, use that one.

How to connect REL to class d?

Connecting to a Class D Amp Using the High Level Cable

How do I connect to REL Speakon?

How to Connect REL T/9x Subwoofer via High Level Connection

Why am I not getting sound from my subwoofer?

Ensure the subwoofer has not been muted. Increase the volume level on the subwoofer. Ensure the speaker settings on the stereo system or TV have been configured properly to use the subwoofer.

Can you connect a subwoofer to any speakers?

In spite of the name, a ‘subwoofer out’ isn’t the best way to connect a subwoofer to a quality music system. The preferred method works even if a preamp doesn’t have special subwoofer or preamp outputs, however, you do need a subwoofer that can accept a “high level” (also called “speaker level”) input.

How do I know if my sub woofer is working?

How To Test A Subwoofer To See If It Works A Quick Test

How do I know if my woofer is working?

Test the sound at a low volume to listen for whether your sub has been blown. If it is distorted, you have a partially blown subwoofer, and if there is no sound at all, it is completely blown. If the subwoofer is receiving its signal via a cable, then check the cable before rushing to conclusions. What is this?

How do I know if my subwoofer is active or passive?

So what is the difference between a passive and active subwoofer? Passive subwoofers require an additional power source like a receiver or amplifier. Active subwoofers include a built-in amplifier and power source and only need to receive an audio source.

Should I leave my REL subwoofer on all the time?

Yes you can leave your subwoofer on all the time as long as it has an auto standby feature. Subwoofers in standby last longer & use less power. Older subwoofers that don’t have this function should be turned off when not in use as electricity escapes in the form of heat, causing the amplifier to get hotter than normal.

Are REL good subwoofers?

The REL 212/SX SUBWOOFERS have increased the overall performance level of my system(s) more than any other piece of equipment or acoustical room treatment I have ever made. Highly recommended!

Where do you place a REL subwoofer?

Because RELs are engineered to produce foundational low bass, it is beneficial to place a single REL into a structural corner at the front of the room, immediately behind the main front speakers. If you have a choice of corners, select the corner that is either built from stronger material (Masonry vs. Sheetrock).

How do I connect my subwoofer to my TV?

You would connect the digital coax cable into the converter port and plug an HDMI cable into the HDMI input on the converters opposite end. You would now be able to connect the HDMI cable into the HDMI input on your subwoofer, and the entire connection would be complete.

How do you set up a rel crossover?

REL Acoustics How To: High & Low Level Tuning Step 4 …

What is a Speakon input?

August 2022) The Speakon (stylized speakON) is a trademarked name for an electrical connector, originally manufactured by Neutrik, mostly used in professional audio systems for connecting loudspeakers to amplifiers. Other manufacturers make compatible products, often under the name “speaker twist connector”.

Should I hear sound from my subwoofer?

Ideally, you should never be able to hear the bass coming from the sub; it should appear to come from the speakers. Try to keep the sub within a few feet of small left front or right front speakers.

How do I reset my subwoofer?

Press and hold the Power button while pressing the Input button and the VOL- button (at the same time). When RESET appears on the front panel display, release the buttons. Unplug the power cord for 30 seconds.

Why is my amp on but no sound?

Possible causes include: The speaker is completely blown. The output transformer is open or otherwise faulty. The speaker jack is not wired correctly.

What wire do I need for my subwoofer?

The speaker wires. If your sub system is going to put out more than 1,000 watts RMS, you can use 12-gauge speaker wire. But 16-gauge speaker wire works well for most installations.

Do I need a special cable for subwoofer?

Any single, standard RCA or subwoofer cable should do just fine. However, if the sub is exhibiting a hum with the RCA/sub cable plugged into it, then maybe try using a “shielded” subwoofer cable. One end of the subwoofer/RCA cable will be plugged into the Subwoofer Output on the back of your receiver.

Can I connect subwoofer to normal amplifier?

To get started with the actual hook-up, you’ll connect the subwoofer to the amplifier using the RCA cable. If you want a stereo hook-up, you’ll need two sets of RCA cables. Connect the subwoofer output to the amplifier input.

How do you test subs?

How To Test Used Subwoofers

Why is my subwoofer humming?

Why does my subwoofer make a humming noise? The voltage difference between a subwoofer electrical ground and the equipment ground can cause it to hum. This can happen because of the irregular current flow in your audio cable. Turning on the volume too high can also cause a hum.

How long should you let a subwoofer break in?

We suggest 20-24 hours for a solid break in time. You can set it with a good clean signal overnight. Once this is done you are ready to install and be on your way.

Why aren t my subs working?

If your subwoofer stopped working, there’s a good chance it was blown. To check, unplug the subwoofer and plug it back in. If it still doesn’t work, try switching the input from AUX to SUBWOOFER on the amp. If that doesn’t work, the subwoofer is probably blown and needs to be replaced.

How do you pair a passive subwoofer?

To do so connect the passive subwoofer to the external amplifier and connect the AV receiver/amplifier to the input of the external amplifier. Here you should use the Subwoofer PRE OUT socket on the A/V receiver/amplifier and connect this to the input of the external amplifier. Was this answer helpful?

Does subwoofer need amplifier?

A subwoofer (sub) is speaker, that is dedicated to the reproduction of low-pitched audio frequencies most commonly referred to as bass. Passive Sub: Passive subs are called passive because they need to be powered by an external amplifier or Audio/Video (A/V) receiver . This is similar to traditional speakers.

Do passive speakers sound better than active?

Active speakers don’t always sound better than passive, but you know what you are getting when you buy them. The amplifier is built-in and is designed to produce optimal audio quality with the speaker. Passive speakers require that you choose your own amplifier.

What is the best way to connect a subwoofer to a receiver?

Using a subwoofer cable (RCA cable), connect the subwoofer to the AV receiver by running the cable from the receiver’s subwoofer output to the subwoofer’s line input. Klipsch subwoofers can be connected via the LFE channel, the white RCA connection, or in a stereo pair by using both the white and red RCA connections.

Where does the subwoofer connect to the radio?

The preferred method of connecting a subwoofer is through the subwoofer output (labeled SUB OUT or SUBWOOFER) of a receiver using an LFE (Low-Frequency Effects) cable. Almost all home theater receivers and processors and some stereo receivers have this type of subwoofer output.

How do you connect a subwoofer to an amplifier?

How to Connect a Subwoofer to an Amplifier

  1. Turn the amplifier and the subwoofer so the backs are facing you.
  2. Locate the plug on your amplifier that is labeled Sub Out, LFE (low frequency effects) Out or Line Out [source: KEF].
  3. Connect the cable that was included with the subwoofer to the amplifier’s terminal.

Can I connect subwoofer to normal amplifier?

To get started with the actual hook-up, you’ll connect the subwoofer to the amplifier using the RCA cable. If you want a stereo hook-up, you’ll need two sets of RCA cables. Connect the subwoofer output to the amplifier input.