How do you bolt a ledger board to a house?

Options for Fastening a Deck Ledger

How do you attach a ledger board to a house roof?

Attach the ledger with 1/2-inch-diameter lag screws or bolts every 16 inches (or as specified by local building codes). Slip stainless-steel washers between the ledger and the siding to allow water to flow behind the ledger. If you can’t get behind the joist to cinch down nuts, use lag screws.

How do you attach a ledger to a house with siding?

Snap a chalk line, cut out the siding and tack up the ledger board. Then slip flashing behind the siding, covering the top edge of the ledger. Start by making an outline on the siding where you want to position the ledger board.

How do you attach a ledger board to a house with wood siding?

Attach-A-Deck works great for mounting a ledger over existing siding. You just drill 2 1/2 in. holes through the siding to the face of the sheathing, apply the Attach-A-Deck fasteners and mount the ledger to the house.

How many lag bolts do you put in a ledger board?

Approved Fasteners

The International Residential Code lists two fasteners for directly attaching ledgers to a house: 1/2-inch-diameter hot-dip-galvanized hex-head machine bolts and 1/2-inch-diameter hot-dip-galvanized lag screws.

Can you attach a ledger board to studs?

Mike Guertin (on Instagram @mike_guertin), a builder and remodeler in East Greenwich, R.I., and a presenter at JLC Live, responds: Yes, it’s technically possible to fasten a deck ledger to the narrow faces of 2-by studs rather than to a solid rim joist.

Can you attach ledger board to fascia?

If you own a two-story home, you can tie the ledger into a band joist. Find the band joist by measuring down from the 2nd story window. When you attach the ledger boards to the fascia, they should be held securely with bolts through the wall, or you can use lag screws.

Can you put a ledger board over siding?

In order to install the ledger board, you usually need to remove the house’s siding. Never install a ledger board over the top of siding no matter what you hear, this can weaken the connection. Aluminum and vinyl siding can easily be removed with tin snips from an area one foot surrounding the ledger board location.

Can you attach patio to house?

How to attach a patio or verandah to a house

How do I attach joists to ledger board?

Installing Deck Joists

How do you flash between deck and house?

How to Install and Flash a Deck Ledger, Start to Finish

How do you waterproof a ledger board?

Deck Ledger Board Flashing Inspection Tips

Can a ledger board be two pieces?

The ledger board doesn’t have to be one continuous board. It can be a series of broken sections if it is solidly attached. This will require extra bolts and installing a 2x nailer across the top of the vent to secure the decking along the house wall.

How much weight can a ledger board hold?

The ledger is 10′ long so every foot of ledger must be designed to carry at least 200 lbs of load.

Can I use 2×6 for ledger board?

2×6 P. Treated bolted as / the size of your deck. It should be 6-8 inches above grade ideally, but you can get ground contact PT that can be placed closer. You want a flashing that won’t react with the larger copper content of the treatment.

Do you use washers with lag screws?

Do Lag Screws Need Washers

Can I use a 2×4 ledger?

The 2×4 ledger is sufficient to support your 2×8 joists, but it needs 4 or 5 16d common nails per stud at 16″ on center to be able to carry the load if it is only carrying the floor load and no roof load.

How do you attach a ledger board to a porch roof?

Lag Screws and Ledger Boards: King of the House Home Inspection

What is a ledger in framing?

A ledger is also a board or beam used to attach a new structure onto the frame of an existing wall. Any project that requires adding to the side of a house or other structure, will include a ledger.

How do you install a patio roof on an existing house?

Cut one side of the horizontal roof beam on an angle so that the rafters sit flush on it. Using your nail gun, attach the horizontal beam and cut the two outer rafters to sit flush on top of the existing house roof. Install the two outer rafters and attach a plain rafter beam to the very edge of the existing roof.

Can I attach patio cover to fascia?

Patio Covers directly attach to your homes fascia board with the included hanger, your fascia board needs to be a minimum of two inches thick and allow enough space for the hanger to attach.

How do you attach pergola to house fascia?

Attach the cut 2-by-8-inch lumber to the outside of the fascia board, using heavy-duty lag screws and washers. The lag screws should be long enough to sink through the fascia board, fascia header and 2 inches into the roof rafters. Having an attachment point at every roof rafter will create a stronger attachment.

Does a ledger board need flashing?

How to Flash a Deck Ledger Board. If you cut out your siding to install a ledger board, careful steps must be taken to ensure that moisture cannot reach your house. Infiltrating rainwater can travel downward, sideways and even upward, so special flashings must be used.

Can you screw into siding?

If you want to attach items to the exterior of a home covered with vinyl siding, you must drill through the siding first and then into the structure of your home to properly secure them. While special tools aren’t necessary to drill into your siding, you must exercise caution when doing so to prevent damage.

How do you attach a ledger board to a stucco house for a patio cover?

How to install a ledger board on existing stucco wall

How do you tie an addition to your house?

How to Connect New Home Addition to Existing Building

How do you attach a roof to the side of a house?

Porch Roof Framing & Shingles – How To